Basic Bios Password Crack

As you can see there are various ways on bypassing/changing BIOS passwords.

I have successfully used all of the options below on various computers many years ago. These methods will work on computers of today. I have updated the Standard BIOS backdoor passwords for current computers made as of last week. ( big grin ).

READ EVEYTHING BEFORE YOU USE ANY METHOD LISTED BELOW.

Basic BIOS password crack - works 9.9 times out of ten

This is a password hack but it clears the BIOS such that the next time you start the PC, the CMOS does not ask for any password. Now if you are able to bring the DOS prompt up, then you will be able to change the BIOS setting to the default. To clear the CMOS do the following:

Get DOS prompt and type:

DEBUG hit enter

-o 70 2e hit enter

-o 71 ff hit enter

-q hit enter

exit hit enter

Restart the computer. It works on most versions of the AWARD BIOS.

Accessing information on the hard disk

When you turn on the host machine, enter the CMOS setup menu (usually you have to press F2, or DEL, or CTRL+ALT+S during the boot sequence) and go to STANDARD CMOS SETUP, and set the channel to which you have put the hard disk as TYPE=Auto, MODE=AUTO, then SAVE & EXIT SETUP. Now you have access to the hard disk.

Standard BIOS backdoor passwords

The first, less invasive, attempt to bypass a BIOS password is to try on of these standard manufacturer's backdoor passwords:

AWARD BIOS

AWARD SW, AWARD_SW, Award SW, AWARD PW, _award, awkward, J64, j256, j262, j332, j322, 01322222, 589589, 589721, 595595, 598598, HLT, SER, SKY_FOX, aLLy, aLLY, Condo, CONCAT, TTPTHA, aPAf, HLT, KDD, ZBAAACA, ZAAADA, ZJAAADC, djonet, %шесть пpобелов%, %Ð'евять пpобелов%

AMI BIOS

AMI, A.M.I., AMI SW, AMI_SW, BIOS, PASSWORD, HEWITT RAND, Oder

Other passwords you may try (for AMI/AWARD or other BIOSes)

LKWPETER, lkwpeter, BIOSTAR, biostar, BIOSSTAR, biosstar, ALFAROME, Syxz, Wodj

Note that the key associated to "_" in the US keyboard corresponds to "?" in some European keyboards (such as Italian and German ones), so -- for example -- you should type AWARD?SW when using those keyboards. Also remember that passwords are Case Sensitive. The last two passwords in the AWARD BIOS list are in Russian.

Flashing BIOS via software

If you have access to the computer when it's turned on, you could try one of those programs that remove the password from the BIOS, by invalidating its memory.

However, it might happen you don't have one of those programs when you have access to the computer, so you'd better learn how to do manually what they do. You can reset the BIOS to its default values using the MS-DOS tool DEBUG (type DEBUG at the command prompt. You'd better do it in pure MS-DOS mode, not from a MS-DOS shell window in Windows). Once you are in the debug environment enter the following commands:

AMI/AWARD BIOS

O 70 17

O 71 17

Q

PHOENIX BIOS

O 70 FF

O 71 17

Q

GENERIC

Invalidates CMOS RAM.

Should work on all AT motherboards

(XT motherboards don't have CMOS)

O 70 2E

O 71 FF

Q

Note that the first letter is a "O" not the number "0". The numbers which follow are two bytes in hex format.

Flashing BIOS via hardware

If you can't access the computer when it's on, and the standard backdoor passwords didn't work, you'll have to flash the BIOS via hardware. Please read the important notes at the end of this section before to try any of these methods.

Using the jumpers

The canonical way to flash the BIOS via hardware is to plug, unplug, or switch a jumper on the motherboard (for "switching a jumper" I mean that you find a jumper that joins the central pin and a side pin of a group of three pins, you should then unplug the jumper and then plug it to the central pin and to the pin on the opposite side, so if the jumper is normally on position 1-2, you have to put it on position 2-3, or vice versa). This jumper is not always located near to the BIOS, but could be anywhere on the motherboard.

To find the correct jumper you should read the motherboard's manual.

Once you've located the correct jumper, switch it (or plug or unplug it, depending from what the manual says) while the computer is turned OFF. Wait a couple of seconds then put the jumper back to its original position. In some motherboards it may happen that the computer will automatically turn itself on, after flashing the BIOS. In this case, turn it off, and put the jumper back to its original position, then turn it on again. Other motherboards require you turn the computer on for a few seconds to flash the BIOS.

If you don't have the motherboard's manual, you'll have to "brute force" it... trying out all the jumpers. In this case, try first the isolated ones (not in a group), the ones near to the BIOS, and the ones you can switch (as I explained before). If all them fail, try all the others. However, you must modify the status of only one jumper per attempt, otherwise you could damage the motherboard (since you don't know what the jumper you modified is actually meant for). If the password request screen still appear, try another one.

If after flashing the BIOS, the computer won't boot when you turn it on, turn it off, and wait